Skip to main content

Mast & Spreaders

Mast & Spreaders - Basic Explaination

Originally, the sole purpose of a mast was a stick to hold the sails up.  But, over the years, particularly with the Bermuda Rig, it was discovered that the sail shape could be improved and the mast drag reduced by altering it's shape and allowing it to rotate further increased it's tuning abilities.  Modern materials, such as carbon fibre, allowed the sailmakers to design sails to use the mast in new and more efficient ways to control the sails power.   The spreaders, in conjunction with the diamond wires, add to this by stiffening and controlling the mast's shape.  However, trimming can be a black art until you discover the secret.


Articles 

 

Ever wondered how stiff your mast is? This question came up as the result of my getting a new Landy DS classic sail for my old DNA. It simply wasn’t delivering the power I was expecting. Everything was tried; downhaul, no downhaul, batten tension, mainsheet tension, rotation, nothing worked. It seemed to have no power mode anywhere. So experts were consulted, both whom happen to be of a similarly magnificence as myself, masswize . Hugh Macgregor was on hand, and offered to swap boats in a race. I beat the 2019 Worlds Classic No. 11 convincingly as a result. This was not a good thing. Hugh declared the boat perfect for spectating, less perfect for racing. So, Mischa Heemskerk was called. Try looking at your mast was the advice. Check the stiffness, was the first thing, and he gave me a technique for doing so.

This was how it was done...

Get a load gauge type weighing scale, the sort of thing big game fishermen weigh their Marlin from. They are quite cheap, but you need one up to 200kg to be safe. Get an old shroud, or forestay and extend the wire to make it about 80% of your mast length, and fix a high load block to the bottom then fasten it to the masthead hook. Fix the bottom of the scale to the traveller track, with a soft shackle, near the centre support if possible. Then run a length of 6mm dyneema through the block, fastening one end to the top of the scales. Get the mainsheet and pull it out and secure the top end of the dyneema to the top mainsheet block, as close to the high load block on your mast wire as possible, and move the traveller into a central position.

 

Rig Stiffness

Next comes the brown trouser time. Switch on the scale and zero the readout. Turn the mast to your usual upwind mast rotation setting Now slowly pull on the mainsheet. This will bend the mast from the top. It is basically the same technique you use to find your batten stiffness – you push the batten vertically down with your palm onto a bathroom scale until the reading stops increasing, and that is the stiffness indication. This is the same system, only you are pulling not pushing. Keep pulling slowly, watching the mast bend and keeping an eye on the scale. It will steadily increase. Then at some point, the scale will start to stop increasing even though you are still gently pulling more bend on. That is point you have reached the maximum stiffness point. You will notice as you slowly release, that you could get, in my case, about 150mm of sheet being let off before the scale started to go down again, indicating that I had reached the max stiffness point. Note this figure, that is your stiffness. Mine was 81kg, so, as you are using a 2:1 purchase on the dyneema (ignore the mainsheet – that is just your force multiplier) it was 160kg stiffness. Indicating this was a Soft-Medium mast. The issue’s cause had been ascertained. Had I been 70-80 kg, it would have been perfect, and explained why I can go uphill like a monster in heavy conditions, but like a barge in less.

I have to admit is was an emotional journey. My ears were straining for every ping and creak that indicated the imminent explosive destruction of my mast, but it was not to be! It simply went back and forward with the pull, almost as though it was designed like that. Obviously I did it in gentle stages and didn’t let in ping back like firing a Roman ballista or siege catapult. The mast won’t break unless there is a fault in there somewhere, or you pull it way beyond the max stiffness point. It was a good exercise to do. Job done, thanks to Mischa, who has done this many times before he claims. I will now look to swap masts with someone for a stiffer untapered example.

However, please note – we take no responsibility whatsoever for your mast exploding using this method. It just shouldn’t do.

 

Landenberger Mast Tuning Tips

Over the past few seasons it has become quite clear that many people who have been experiencing speed or power problems have had little basic knowledge of what they can do with the mast settings. It is clear what do with the cunningham, simply pull on it to get the pressure out of the sail as you need, but often the mast is left unattended to, as a last priority. In fact it is one of the most important speed controls on the boat. It is important to understand how to use it, and what you want to have in the sail shape for different conditions. It is not so easy to just come up with numbers and angles that will suit every mast and sail so I will try to make some key points to help understand this correctly. 

  1. The more pre bend set in the mast the more effect mast rotation has on the sail shape.

  2. The effect of the spreaders means that the more the mast is rotated backwards, the more the lower mast section can bend forward (in the direction of the boat) and the stiffer the top section becomes. Leaving the cunningham tension out of the discussion at the moment, the result would be that the sail becomes flatter in the bottom and fuller in the top.

  3. Rotating the mast more forward allows the spreader to start to work and the lower mast section becomes stiffer in the forward direction and the top becomes softer backwards. The result is the sail will become deeper in the bottom and flatter in the top.

  4. Cunningham pressure flattens the sail and will tend to flatten the top more than the bottom since the top of the mast is unsupported and more free to bend.

Understanding the sail shape that works best in the differing conditions is then very important. For example in Flat water you would like to have a very even profile through the sail from top to bottom with good power in the top and the possibility to pull the mainsheet quite hard without stalling the back of the sail. On flat water you can sheet hard and point higher. By wave conditions you would want good power down low in the sail and have the top more open and twisted. This gives you power and the twisted top allows the boat to accelerate easily letting you steer around more and power the boat through the waves easier. Generally you can’t point as high as the boat on flat water but because of the waves you can achieve a much better VMG (velocity made good).

The typical example is that with increasing wind the sailor will pull the Cunningham hard but not adjust the mast rotation to go with it. The effect of the Cunningham is flattening the sail, but more in the top. This allows the leech to open. The boat may feel ok but often the leech is to open and you can’t point high enough. This setup can be good in big waves but on flat water the sailor would like to have the leech standing much straighter so they should rotate the mast further back. If you go back to our original points you can see that the mast becomes stiffer in the top and can bend more in the bottom. This is therefore powering up the top and flattening the bottom of the sail. With the Cunningham pressure you can sheet on hard and point high with good speed.

The other typical mistake which occurs, is that the sailor by strong wind, simply pulls the mast back in line with the boom and pulls full Cunningham pressure. Because the mast rotation is too far back the sail becomes too full in the top and too open in the bottom. The sail will have a lot of twist which some sailors think is good for strong wind, but because of the top of the mast reaching its maximum stiffness in the aft direction of the boat the sail will remain too full in the top. The end result is a sail which is twisted to far and with too much profile for the strong wind. The twist causes you to loose pointing ability and the depth is causing excessive drag, just slowing you down. You are in effect going slower and lower than the correctly trimmed boats.

Spreader rake is also another significant factor in setting up you rig. It also plays a part in how much the rotation angle affects the depth of the sail. That can be a whole subject of its own, so for now I make just a few comments. Try to think of pre-bend as controlling the position the mast takes its bend. The more pre-bend you make in the mast the lower the mast likes to bend. The lower the mast tries to bend the straighter the top section becomes. The flatter the pre-bend the more the top section tries to bend. The normal reaction of sailors is to increase the pre-bend for strong wind to flatten the sail and reduce it in light wind to increase power.  Principally that is correct, but it must be incorporated with the rotation to get the right balance in the sail. Like most things, too much or too little can be harmful. It is a great failure made by many sailors to flatten the spreader angle to far reducing the pre-bend in the mast to almost straight. For light wind this is doing more harm than good. The heavier sailors also often request more luff curve because they are looking for power.  With more luff curve and flatter spreaders light wind speed can quickly come to an end. The sail will become very full down low with a deep entry angle from the mast and a very closed leech section. When you get the first wind in the sail you may get a feeling of power, but you may also experience the boat just wanting to fly a hull but not wanting to go easily forward. The boat will not point and will not accelerate.

In many cases it is actually better to go the other way. By very light wind you can increase the pre-bend to open the lower part of the sail and reduce the entry angle of the sail behind the mast. With the rotation angle set correctly to get the head standing up just the right amount you can be very fast. Just remember flat is fast and deep is slow. It has a lot more to do with entry and exit angles of the sail to achieve height and power.

Amongst sail makers there are many different ideas, and history has proven that there are many ways to build fast sails. The most important thing is that the sailor can understand how the sail should work and manage it well. Also restrictions on materials and designs in the boats themselves change the way the sail has to work to achieve the best results. We design our A class sails to allow the mast to be rotated well back. The reason being, that the mast itself creates a lot of profile over the rig and therefore it is very important to be able to reduce the wind age over the mast by rotating back as the wind increases. At the same time the sail must flatten rather than get fuller. That is the secret to success.